Matthew Westall Bee Vac Photos

275

Movement of airflow regulator.

Movement of airflow regulator.

Vacuum hose side.

Vacuum hose side.

Side with vacuum hose removed.

Side with vacuum hose removed.

Both vacuum hose & 2" insert removed - see both inner box & outer box matching up.

Both vacuum hose & 2″ insert removed – see both inner box & outer box matching up.

Removable vacuum head.

Removable vacuum head.

Showing top with vacuum removed - able to connect any wet-vac with 2" hose.

Showing top with vacuum removed – able to connect any wet-vac with 2″ hose.

BeeVac with top opened - see inner box

BeeVac with top opened – see inner box.

Inner box partially removed.

Inner box partially removed.

Inner box on display - with bottom open, shows screening on both sides.

Inner box on display – with bottom open, shows screening on both sides.

Top of inner box showing close-able vacuum hose opening.

Top of inner box showing close-able vacuum hose opening.

Inside of outer box - shows three spacers which hold the inner box.

Inside of outer box – shows three spacers which hold the inner box.

Top of outer box from inside - shows vent for airflow regulator.

Top of outer box from inside – shows vent for airflow regulator.

Outer box - front view (latch).

Outer box – front view (latch).

Outer box - right side view (hose).

Outer box – right side view (hose).

Outer box - back view (hinges).

Outer box – back view (hinges).

BeeVac open with inner box partially removed.

BeeVac open with inner box partially removed.

Inner box - hose-side, shows placement of close-able flap while inserted into the BeeVac.

Inner box – hose-side, shows placement of close-able flap while inserted into the BeeVac.

Inner box - movement of inside flap.

Inner box – movement of inside flap.

Inner box - movement of inside flap (close this flap until it hits the vacuum hose).

Inner box – movement of inside flap (close this flap until it hits the vacuum hose).

Inner box - movement of inside flap (fully closed after removing hose @ same time - close by pushing on edge of flap).

Inner box – movement of inside flap (fully closed after removing
hose @ same time – close by pushing on edge of flap).

Outer box - showing inside flap closed on inside box.

Outer box – showing inside flap closed on inside box.

Inner box - removal of inner box, now with flap closed.

Inner box – removal of inner box, now with flap closed.

Outer box - hose removal - notice lining of silicon on outside bead for good fit (note: VERY important that the size of inside & outside holes both match up & fit to the 2" hose adapter snugly!).

Outer box – hose removal – notice lining of silicon on outside bead for good fit (note: VERY important that the size of inside & outside holes both match up & fit to the 2″ hose adapter snugly!).

Showing how I drilled the inner box holes, placing the inner box within the BeeVac & drilling through the vacuum hose hole.

Showing how I drilled the inner box holes, placing the inner box within the BeeVac & drilling through the vacuum hose hole.

BeeVac - complete.

BeeVac – complete.

Inner box - opened, upside down, showing screens on both sides.

Inner box – opened, upside down, showing screens on both sides.

Inner box - opened, detail of plastic rails which floor slides on (I used common wall protector) showing bottom board inserted into rails.

Inner box – opened, detail of plastic rails which floor slides on (I used common wall protector) showing bottom board inserted into rails.

Inner box - front with vacuum hole & flap.

Inner box – front with vacuum hole & flap.

Inner box - mesh sides (note shorter wood side is closer to vacuum hole - with longer wood serving as an air buffer at the rear).

Inner box – mesh sides (note shorter wood side is closer to vacuum hole
– with longer wood serving as an air buffer at the rear).